HV SMPS design

This is the place for any magazine-related discussions that don't fit in any of the column discussion boards below.
Post Reply
User avatar
haklesup
Posts: 3136
Joined: Thu Aug 01, 2002 1:01 am
Location: San Jose CA
Contact:

HV SMPS design

Post by haklesup »

Has anyone seen a schematic or chipset that can accomplish an SMPS power supply with +/- 140V DC, 250mA? (and Universal AC input).

Most designs top out at 36V or perhaps 48V. Were still using a linear supply here and even if I could put an AC universal 110V/220V auto selector in front of it that would be useful but that's an unusual solution too. Any suggestions how to eliminate that manual 110V/220V selector switch from equipment that needs high internal DC voltage? I don't even see any DC-DC in the wanted range
User avatar
dacflyer
Posts: 4748
Joined: Fri Feb 08, 2002 1:01 am
Location: USA / North Carolina / Fayetteville
Contact:

Re: HV SMPS design

Post by dacflyer »

when you say +/- 140V DC is that -70-0-+70, or somewhere about 140v ?
what is this being used on.
User avatar
haklesup
Posts: 3136
Joined: Thu Aug 01, 2002 1:01 am
Location: San Jose CA
Contact:

Re: HV SMPS design

Post by haklesup »

I mean 240V pole to pole with 0V in the middle or -140, 0V, +140V. It's used as a primary unregulated source for a 2 channel +/-100V, 100mA 4 quadrant SMU. I don't expect to find anything off the shelf and want to design one from scratch but can't even find a chipset that could work. I'm not totally versed in SMPS design, so I was hoping to find a datasheet for inspiration. The linear design (using a transformer) is simple but I'm searching for a more compact lighter weight or at least to get rid of the 110/220V switch.
User avatar
dacflyer
Posts: 4748
Joined: Fri Feb 08, 2002 1:01 am
Location: USA / North Carolina / Fayetteville
Contact:

Re: HV SMPS design

Post by dacflyer »

gotchya... I'll look around a bit, I'll see if i find anything..
User avatar
Janitor Tzap
Posts: 1707
Joined: Sat Aug 12, 2006 5:17 pm
Contact:

Re: HV SMPS design

Post by Janitor Tzap »

Here's a free PDF download site that has several books on SMP's.
https://www.pdfdrive.com/switching-powe ... 37735.html


Signed: Janitor Tzap
User avatar
haklesup
Posts: 3136
Joined: Thu Aug 01, 2002 1:01 am
Location: San Jose CA
Contact:

Re: HV SMPS design

Post by haklesup »

you know, I'd be just as happy with a circuit that detects 110V or 220V at the input and toggles a relay or FET switch to direct voltage to the proper primary windings of the transformer. I'm thinking of a way to do that reliably and safely. Thats not SMPS but it satisfies my main goal of eliminating the manual voltage switch.
User avatar
dacflyer
Posts: 4748
Joined: Fri Feb 08, 2002 1:01 am
Location: USA / North Carolina / Fayetteville
Contact:

Re: HV SMPS design

Post by dacflyer »

I saw this,, maybe it might give you some insight...

https://forum.allaboutcircuits.com/thre ... 0v.162071/
User avatar
haklesup
Posts: 3136
Joined: Thu Aug 01, 2002 1:01 am
Location: San Jose CA
Contact:

Re: HV SMPS design

Post by haklesup »

Thanks, one suggestion of that thread of a relay with 220V coil is workable but I consider unsafe and unreliable for this application, but I did just find this gadget that just might unlock the door to my effort

https://www.ebay.com/itm/311864741981?c ... gJp3PD_BwE

This device could drive a 5V coil relay and may be more reliable. The relay can toggle a DPDT contact set that the manual switch used to provide. It looks easy enough to reverse engineer. It's certainly safer by isolating via opto-coupler the High AC and low DC voltages.

I doubt I will go all the way to uController enabled power supply sequencing, but this seems to be how it might be done.
https://www.instructables.com/Arduino-A ... -Detector/
Post Reply

Who is online

Users browsing this forum: Ahrefs [Bot] and 27 guests