replacing parts on printed circuit
-
- Posts: 4
- Joined: Sun Sep 03, 2017 8:57 am
- Contact:
replacing parts on printed circuit
I recently tried to replace two capacitors on a Philips TV 'Backlight inverter board'; however, I could not get the solder to 'melt'. Do I need a special soldering iron? Any suggestions appreciated!
Re: replacing parts on printed circuit
What kind of soldering iron? How many watts ? Is the tip of the iron clean ? A dirty soldering iron tip will not transfer the heat needed to melt the solder. An adjustable one, with the temp turned way down won't work either. When you try it again, try adding a little new solder to it to help make it flow.
Re: replacing parts on printed circuit
lead free solder melts higher than tin-lead but not that much higher unless it is an exotic uncommon alloy. Your iron could be underpowered for the joint (doubtful on an inverter board) or as suggested some flux or more [flux core] solder to improve the thermal transfer at the tip. I never solder without adding flux (paste or liquid), the time it takes to clean is usually less than the problems that not using it can cause.
-
- Posts: 1918
- Joined: Fri Aug 22, 2003 1:01 am
- Location: Izmir, Turkiye; from Rochester, NY
- Contact:
Re: replacing parts on printed circuit
I argee with Gerty. Wattage and tip size of iron?
You did not specify capacitor type. But the 12W, 1/16" diameter tip I use for soldering IC pins won't touch electrolytic cap leads on wide traces. For that I use a 50W iron with 1/8" diameter tip.
Cheers,
You did not specify capacitor type. But the 12W, 1/16" diameter tip I use for soldering IC pins won't touch electrolytic cap leads on wide traces. For that I use a 50W iron with 1/8" diameter tip.
Cheers,
Dale Y
-
- Posts: 4
- Joined: Sun Sep 03, 2017 8:57 am
- Contact:
Re: replacing parts on printed circuit
Welder 140 watt. Cleaned tip, etc. Nothing!
-
- Posts: 1918
- Joined: Fri Aug 22, 2003 1:01 am
- Location: Izmir, Turkiye; from Rochester, NY
- Contact:
Re: replacing parts on printed circuit
Does it get hot?
You wouldn't believe the number of times tha answer to "Is it plugged in?", is "Oops, no!"
You wouldn't believe the number of times tha answer to "Is it plugged in?", is "Oops, no!"
Dale Y
-
- Posts: 4
- Joined: Sun Sep 03, 2017 8:57 am
- Contact:
Re: replacing parts on printed circuit
Temperature at tip: 125+
-
- Posts: 1918
- Joined: Fri Aug 22, 2003 1:01 am
- Location: Izmir, Turkiye; from Rochester, NY
- Contact:
Re: replacing parts on printed circuit
60/40: melts between 183–190 °C (361–374 °F)
Not even close! You need a new iron.
Cheers
Not even close! You need a new iron.
Cheers
Dale Y
Re: replacing parts on printed circuit
Indeed your soldering iron is too low in temperature. I use a Weller WTCTP series iron, and the tips are preset to 600,700, and 800°F. Also, smaller tips store less heat so they cool faster on heavy PCB traces. Us old timers used Weller soldering guns, which are still made, and the infamous Ungar ceramic soldering element and 'cigarette lighter'. In the days of point to point wiring, chassis connections were common and a lot of heat was needed. They are still handy to get shields and heat sinks off the board or when soldering ground braid, which is not seen too often anymore.
Side Note:
The WTCTP iron uses a unique soldering tip that has a slug of a special alloy metal attached to its back end. This slug attracts a magnetic switch in the iron handle to turn the iron on and then releases the switch at the slug's Curie point. (Temperature point where the metal loses it's magnetic attraction) The tips, available in many styles, are stamped 6,7,8 for the temperature. It's a great iron, quick recovery and with thousands of PCB connections, and some maintenance, it is still going strong.
Side Note:
The WTCTP iron uses a unique soldering tip that has a slug of a special alloy metal attached to its back end. This slug attracts a magnetic switch in the iron handle to turn the iron on and then releases the switch at the slug's Curie point. (Temperature point where the metal loses it's magnetic attraction) The tips, available in many styles, are stamped 6,7,8 for the temperature. It's a great iron, quick recovery and with thousands of PCB connections, and some maintenance, it is still going strong.
Len
“To invent, you need a good imagination and a big pile of junk.” (T. Edison)
"I must be on the way to success since I already have the junk". (Me)
“To invent, you need a good imagination and a big pile of junk.” (T. Edison)
"I must be on the way to success since I already have the junk". (Me)
-
- Posts: 4
- Joined: Sun Sep 03, 2017 8:57 am
- Contact:
Re: replacing parts on printed circuit
Weller WTCTP is little pricey for me.
Anyone familiar with: SOAIY Full Set 60W Adjustable Temperature ON/OFF Switch Welding Soldering Iron Kit
Anyone familiar with: SOAIY Full Set 60W Adjustable Temperature ON/OFF Switch Welding Soldering Iron Kit
Re: replacing parts on printed circuit
Hakko is a good alternative to Weller if you want a full featured station with lots of tips to choose from. Probably any 50W or greater iron will be plenty, off brands might not last as long though.
Who is online
Users browsing this forum: No registered users and 162 guests