Diode forward/reverse resistance measurement

This is the place for any magazine-related discussions that don't fit in any of the column discussion boards below.
Post Reply
User avatar
vinod
Posts: 148
Joined: Fri Feb 12, 2010 12:37 pm
Contact:

Diode forward/reverse resistance measurement

Post by vinod »

See the diagrams attached herewith.

Diode Diode arrangement

DFR- Diode Forward Resistance
DRR- Diode Reverse Resistance

Both are identical diodes and the multimeter is set in auto range(resistance mode).

MM shows 43M Ohm instead of OL! ( If I connect a multimeter positive terminal at A & negative terminal at B )

Diode Resistor arrangement

Here connecting the MM in forward mode reads 6KOhm against expected value of 1K+DFR

In reverse mode shows OPEN as expected.
Attachments
diode resistor.png
diode resistor.png (1.03 KiB) Viewed 7586 times
diode.png
diode.png (1016 Bytes) Viewed 7586 times
@VinodQuilon
User avatar
Externet
Posts: 1888
Joined: Fri Feb 01, 2002 1:01 am
Location: Mideast USA
Contact:

Re: Diode forward/reverse resistance measurement

Post by Externet »

For every different multimeter, different readings in the resistance scale will be obtained when probing a diode, because diodes resistance is not a characteristic nor a specification, but an apparent equivalent depending on the voltage supplied by the multimeter leads and other factors as current, temperature, internal resistance of the meter...

So forget about measuring resistance in a diode. The resistance scale is for resistors, the diode check in a multimeter shows the voltage drop of the junction. And not all meters will work/show the value as for higher Vf as in LEDs.
- Abolish the deciBel ! -
User avatar
haklesup
Posts: 3136
Joined: Thu Aug 01, 2002 1:01 am
Location: San Jose CA
Contact:

Re: Diode forward/reverse resistance measurement

Post by haklesup »

Yes, since a diode is non linear, the value of equivalent resistance is not very meaningful except as a qualitative comparison. The value you get is very much dependent on the drive voltage and ultimately the current that induces, tiny changes in V can have large changes in I at various points on the characteristic. The meter may assume a linear equivalent between 0V, 0A and the operating point and the operating point changes with range, generally use the lowest range.

Diode check mode on a DMM is more useful telling you the forward voltage.
Rodney
Posts: 162
Joined: Sat Aug 31, 2002 1:01 am
Location: Titusville, FL USA
Contact:

Re: Diode forward/reverse resistance measurement

Post by Rodney »

The only good way I have found to check the impedance of a diode is to use an oscilloscope. Use the X and Y axis. put the current through the diode on one axis and the voltage across it on the other axis and power it with an AC voltage. The slope of the trace on the scope will be an indications of the impedance at any specific current which you can easily measure.
User avatar
haklesup
Posts: 3136
Joined: Thu Aug 01, 2002 1:01 am
Location: San Jose CA
Contact:

Re: Diode forward/reverse resistance measurement

Post by haklesup »

Rodney, What you have described is using a oscilloscope like a curve tracer. There are a variety of curve tracer circuits that will allow one to better select ranges when doing it like that and are easy to build. Of course, if you know someone with a curve Tracer, then you can just do it the formal way.

You can also manually construct a curve trace using graph paper and measuring the current and voltage as you incrementally increase one or the other.
RichMarkley
Posts: 1
Joined: Tue Apr 02, 2019 2:45 pm
Contact:

Re: Diode forward/reverse resistance measurement

Post by RichMarkley »

Some scopes, like the Rohde & Schwarz RTC1000, have a built-in component test function that can make this measurement. In addition to diodes, you can use this feature to test capacitors, resistors, transistors, thyristors, coils, and resulting circuits such as rectifiers. This can really come in handy when troubleshooting electronics circuits, especially when you don't have a schematic.
User avatar
Lenp
Posts: 1529
Joined: Thu Oct 26, 2006 8:11 pm
Location: Maryland
Contact:

Re: Diode forward/reverse resistance measurement

Post by Lenp »

I'm not sure if this discussion is about component specifications or troubleshooting. Curve tracers and component testers are needed for specification evaluation, but a good front to back ratio usually tells the story for open/short for troubleshooting.
Len

“To invent, you need a good imagination and a big pile of junk.” (T. Edison)
"I must be on the way to success since I already have the junk". (Me)
User avatar
Externet
Posts: 1888
Joined: Fri Feb 01, 2002 1:01 am
Location: Mideast USA
Contact:

Re: Diode forward/reverse resistance measurement

Post by Externet »

[ Thread is from 2013 ]
- Abolish the deciBel ! -
User avatar
haklesup
Posts: 3136
Joined: Thu Aug 01, 2002 1:01 am
Location: San Jose CA
Contact:

Re: Diode forward/reverse resistance measurement

Post by haklesup »

Ya, its old. Component testers produce a curve that resembles a curve tracer but is generally uncalibrated and had less control over settings. They also use a faster scan rate 50 or 200 hz in this case which produces the looping effect caused by inductors and capacitors. A curve tracer for characterization purposes would be more flexible, more accurate and sweep slower to avoid the looping and just get the measurement from the semiconductor. In this case, the 50Hz rate should produce curves similar to the old Tektronics curve tracer sweep rate which was derived from a built in variac but with less control over settings.
Post Reply

Who is online

Users browsing this forum: No registered users and 37 guests