CD4017 used as stepper on Poptronics 04/01 ?

This is the place for any magazine-related discussions that don't fit in any of the column discussion boards below.
Post Reply
User avatar
Externet
Posts: 1853
Joined: Fri Feb 01, 2002 1:01 am
Location: Mideast USA
Contact:

CD4017 used as stepper on Poptronics 04/01 ?

Post by Externet » Mon Jan 22, 2007 11:34 pm

Hi all.
The 04/2001 issue of Poptronics may have a schematic using a CD4017 +ULN2003 to step a motor; can someone please confirm/describe circuit?
My 25+ year magazine collection is in storage far, very far... :sad:

Is it like this one? :

http://www.bvsystems.be/stepper.jpg

Thanks,
Miguel

User avatar
Edd
Posts: 885
Joined: Sun Jan 27, 2002 1:01 am
Location: Dallas Tx
Contact:

Post by Edd » Tue Jan 23, 2007 3:25 pm

.

Eyyyyyy..Miguel...que Paaaaaaaaaaasa ?

Now quick scanning within those articles for that month I saw NONE that were specific in using that ULN200X series of interfacing..nor used as a pre motor driver..but just relevant to the 4017 aspect there was one article on it...with a further follow up the next month, but it was merely driving a large multiplexed mass of LED's

Wasn't sure which / if any of the following was applicable to your situation so I am sending you "the whole ball 'o twine"...and you can unravel it accordingly, should it pertain to your application .

Now looking within those articles.

The first application is certainly easier in its current consumption mode, with its incorporating a C-mos gate section as its osc.

Also, any further info as to the initial source that said that info was actually in that issue would be helpful.

Ref.....Pulled Oversized and then J-pegged up for clarity:

http://img228.imageshack.us/img228/499/4017pg16oc.jpg
http://img120.imageshack.us/img120/6789/4017pg25nb.jpg
http://img120.imageshack.us/img120/5889/4017pg36oe.jpg
http://img267.imageshack.us/img267/3710/4017pg43cm.jpg


73's de Edd
[email protected] ...........(Interstellar~~~~Warp~~~~Speed)
[email protected]..........(Firewalled*Spam*Cookies*Crumbs)
:grin: :razz: :grin:


You can't have everything. Where in the world would you put it?.....Image

.

Newz2000
Posts: 507
Joined: Wed May 18, 2005 1:01 am
Location: Des Moines, Iowa, USA
Contact:

Post by Newz2000 » Tue Jan 23, 2007 3:34 pm

Miguel,
I have a circuit similar to that on my breadboard right now... I run two steppers and instead of the 4017 I use a PIC that simply does something like:
rb0 = 1;
rb4 = 1;
wait
rb0 = 0;
rb4 = 0;
rb1 = 1;
rb5 = 1;
wait
etc.

I used it to experiment with different voltages/delays to see how fast the motors could turn.

The stepper motors work fine. Your 555/4017 means they can only go one direction. I'm sure you know most of this though... :-)

User avatar
Externet
Posts: 1853
Joined: Fri Feb 01, 2002 1:01 am
Location: Mideast USA
Contact:

Post by Externet » Tue Jan 23, 2007 10:05 pm

Hello Ed, thanks for being so kind taking the work of scanning the pages !
Seems I was misled, the article does correspond to the 4017 but not to drive a stepper motor with it.
Very nice from you, hope I can be of help any time.

Newz2000 : I may throw up with software, am avoiding PICs because of that.
Since I dumped my programmer title to the garbage can in 1971... been looking for a new brain :sad: .
I just need to step one step every minute from an atomic clock pulse, the 4017 should work just fine.

Cheers,
Miguel :grin:

rshayes
Posts: 1286
Joined: Tue Mar 04, 2003 1:01 am
Contact:

Post by rshayes » Wed Jan 24, 2007 3:09 am

A dual flip-flop can be used to generate the patterns for driving a stepping motor. It is wired as a two bit shift register, with the input to the first stage coming from the complement output of the second stage.

This gives the sequence:

00
10
11
01
00, etc.

The four outputs are (for two complete cycles):

01100110 (first stage true)
00110011 (second stage true)
10011001 (first stage complement)
11001100 (second stage complement)

This is known as a shift counter, Johnson counter, or switch tail ring counter.

Post Reply

Who is online

Users browsing this forum: No registered users and 38 guests