Custom Electronics Service ?

This is the place for any magazine-related discussions that don't fit in any of the column discussion boards below.
Post Reply
AJAJ
Posts: 1
Joined: Mon May 10, 2010 3:31 pm
Contact:

Custom Electronics Service ?

Post by AJAJ » Mon May 10, 2010 3:48 pm

I am trying to find someone who can build simple electronic devices I need now and then. These things are not for production, just for my use. (I'm a crime scene analyst involved in ballistics and other forensic research). I don't need engineering or custom PCB's or polished housings; most of what I need can be constructed from modified off the shelf items. I used to know a retired EE who built things for me but he passed away.

Right now I need a simple talkback paging/PA system. One station with an intercom type box (with speaker) and a push to talk switch that will talk over a (10 watt or so) loudspeaker in a different area (wired, not wireless). And the people in the other area can just shout back at the speaker (without pushing a button) and be heard at the master station. (Yes, there are many similar systems commerically available but most work through a telephone system or are complex items with many stations or Radio Shack type intercoms that don't have the loudspeaker power I need.)

I thought I recalled ads from people willing to build such things in Nuts & Volts but I can't find them now.

Thanks,

Alex Jason
[email protected]

User avatar
Externet
Posts: 1844
Joined: Fri Feb 01, 2002 1:01 am
Location: Mideast USA
Contact:

Re: Custom Electronics Service ?

Post by Externet » Mon May 10, 2010 5:28 pm

Hello and welcome.
It has been a loooong time since I played with those.
From what I remember, it is an audio amplifier with output stepped up to 70V, The speaker end picks voice and the normally closed contact of the base 'unpushed' button routes its signal to the amplifier input that selects the local base speaker.
When the button is pushed, its contacts route the local speaker to the amplifier input and the amplifier output is routed to the remote speaker.

Nice project!
Miguel
- Abolish the deciBel ! -

User avatar
jwax
Posts: 2182
Joined: Mon Feb 09, 2004 1:01 am
Location: NY
Contact:

Re: Custom Electronics Service ?

Post by jwax » Wed May 12, 2010 10:59 am

How about an off-the-shelf PA system with the speaker in the remote area, and a baby monitor in the remote area to talk back to the base?
An option would be to "Silence" the baby monitor pickup (from the base?)
Loads of possibilities!
John

P.S. Welcome to the forum AJAJ! :grin:

psycho
Posts: 388
Joined: Thu Jan 10, 2008 8:13 pm
Location: Northwest Indiana
Contact:

Re: Custom Electronics Service ?

Post by psycho » Wed May 12, 2010 3:09 pm

To answer your main question, you might try looking for a local ham radio operator. Most of them (esp. the old timers) know quite a bit about electronics. If I knew where you are from, I would look.

You might look in your phone book for places that sell radio equipment (for ham radio) - tho there probably won't be any listings. Try Two-Way radio, too. Also any place that sells electronic components - the people who work there may know someone who could help. You could try radio-shaft, too - maybe one of their customers is into electronics...

Hope it helps,
Kevin

User avatar
Lenp
Posts: 1434
Joined: Thu Oct 26, 2006 8:11 pm
Location: Maryland
Contact:

Re: Custom Electronics Service ?

Post by Lenp » Wed May 12, 2010 4:28 pm

AJAJ
Check your email!
Len
Len

“To invent, you need a good imagination and a big pile of junk.” (T. Edison)
"I must be on the way to success since I already have the junk". (Me)

Post Reply

Who is online

Users browsing this forum: No registered users and 13 guests