Search found 326 matches
- Wed Aug 13, 2014 4:49 pm
- Forum: General Discussion
- Topic: Lasers anyone?
- Replies: 4
- Views: 2748
Re: Lasers anyone?
Note #3 says: you have to add at least 1000khz signal on the yellow wire for TTL effect. if not, you cannot get the TTL effect 1000Khz is 1Mhz, is this a typo or is the unit not 100Khz as stated? Then again maybe it's just broken. From what I have just recently researched I believe connecting the TT...
- Tue Aug 05, 2014 6:17 pm
- Forum: General Discussion
- Topic: microcontroler circuit design question / new digital scope
- Replies: 7
- Views: 8444
Re: Tektronix 465 scope / micro input question
samt_32,
Welcome to the Forum!
I don't have an answer for the type of scope that may be required but have you tried adjusting the duty cycle of the 555 circuit?
Steve G
Welcome to the Forum!
I don't have an answer for the type of scope that may be required but have you tried adjusting the duty cycle of the 555 circuit?
Steve G
- Wed Jan 01, 2014 7:11 am
- Forum: General Discussion
- Topic: new challenge..
- Replies: 18
- Views: 8464
Re: new challenge..
there are no coax connections on the direct tv You're right Im looking at a new Direct TV receiver box and there are no coax outputs. Those guy's aren't dumb, looks like you will need to order a second receiver in my opinion. Or you could use a RF modulator connected to the composite video output o...
- Wed Jan 01, 2014 5:47 am
- Forum: General Discussion
- Topic: new challenge..
- Replies: 18
- Views: 8464
Re: new challenge..
NEW tv's do not have tv output on them.. lots of HDMI and such, but NO coax tv output I'm missing something here. Do you mean coax TV input? Because I've never seen a coax TV output on any TV before. VCRs and cable boxes but not TVs. All TVs including the new ones have a coax Input. You would need ...
- Tue Dec 31, 2013 4:55 pm
- Forum: General Discussion
- Topic: i need help with color organ problem.
- Replies: 8
- Views: 3689
Re: i need help with color organ problem.
Experiment with decreasing the value of the .04 and/or C6is there a way to adjust something for a lil bit higher frequency
Steve G
- Tue Dec 31, 2013 4:20 pm
- Forum: General Discussion
- Topic: i need help with color organ problem.
- Replies: 8
- Views: 3689
Re: i need help with color organ problem.
That increases the gain of the filter thus a brighter LED with the same signal input level is all.but in the notes it says to increase brightness increase resistance of R11
Steve G
- Tue Dec 31, 2013 2:11 pm
- Forum: General Discussion
- Topic: i need help with color organ problem.
- Replies: 8
- Views: 3689
Re: i need help with color organ problem.
dac, I've got the original book that schematic came from " The Forrest Mims Circuit Scrapbook" and it is indeed different from your version. Here's the schematic of the high pass filter in my book: The .04uf capacitor is the key! The negative input of the opamp needs to be AC coupled as th...
- Sun Nov 24, 2013 6:38 am
- Forum: General Discussion
- Topic: Charging battery with solar panel...
- Replies: 11
- Views: 5887
Re: Charging battery with solar panel...
It will depend on the charging current required and how much the wattage of the cell drops on those cloudy/hazy days.
Steve G
Steve G
- Fri Oct 11, 2013 4:03 pm
- Forum: General Discussion
- Topic: Will This SMPS Run a 5½" Circular Saw?
- Replies: 4
- Views: 2866
Re: Will This SMPS Run a 5½" Circular Saw?
fine-tune, From one of the reader reviews: A customer from SLAYTON, MN USA Output connections The pinout for the output 8-pin DIN is: 1,2,4,6 are +V 3,5,7,8 are Gnd I would worry that the power supply might "kick off" when the saw is first powered up. Heavy in rush current or the blade sta...
- Wed Sep 18, 2013 5:41 am
- Forum: General Discussion
- Topic: Newbie:Hello World...trying to configure LED lights
- Replies: 3
- Views: 2528
Re: Newbie:Hello World...trying to configure LED lights
The signal from a receiver headphone jack is low voltage analog and probably will need some amplification to drive the LEDs. A LM386 is practical for the amp part and this could drive several transistors which drive the LEDs. Something like the circuit below. Which can be heavily modified depending ...
- Tue Sep 17, 2013 10:31 am
- Forum: General Discussion
- Topic: Newbie:Hello World...trying to configure LED lights
- Replies: 3
- Views: 2528
Re: Newbie:Hello World...trying to configure LED lights
Roadhound welcome to the forum.
For the FM transmitter you could start here:
http://www.canakit.com/universal-fm-tra ... uk108.html
Steve G
For the FM transmitter you could start here:
http://www.canakit.com/universal-fm-tra ... uk108.html
Steve G
- Fri Aug 16, 2013 6:04 am
- Forum: General Discussion
- Topic: Wiring issues
- Replies: 18
- Views: 12483
Re: Wiring issues
Lets see here, we have:
blow guns
RC cars
slingshots
ferrets.
I vote the ferret
Steve G
blow guns
RC cars
slingshots
ferrets.
I vote the ferret
Steve G
- Thu Aug 15, 2013 2:13 pm
- Forum: General Discussion
- Topic: Wiring issues
- Replies: 18
- Views: 12483
Re: Wiring issues
Len, I wouldn't call this new or fancy and depends on how much access you have , but when I worked for a sound company years ago we would shoot pull string above the ceiling down long corridors and hallways using a homemade "blow gun". Just a bottle of compressed air and a two or three foo...
- Thu May 16, 2013 6:43 am
- Forum: General Discussion
- Topic: electronic dice
- Replies: 13
- Views: 6788
Re: electronic dice
avionicsmaster1958 said: [quote][ I think PicBASIC is easier than PICAXE because it is the basic language where, to me, PICAXE is a lot like C. Which in itself is bad and good. Bad to me as it's a bit harder to learn but I think PICAXE is more efficient and you can pack more bits into a chip/quote] ...
- Sun May 05, 2013 5:13 pm
- Forum: General Discussion
- Topic: electronic dice
- Replies: 13
- Views: 6788
Re: electronic dice
Would a PIC be a good candidate? Pic is a good candidate, although I started out in and still use the PICAXE family of micros. These are Pic microchips pre-programmed with the PICAXE bootstrap code. I believe this is the easiest, least expensive and most simple way of getting into micro's. Check ou...