T&L Publications

Craftsman radial arm Model 113.2310 Motor Plate Model KS48 DE-175 CLASS B, E37845, MFG. NO. 5 74 1 Motor starting coil burnt probably due to motor disconect SW remaing closed after start up. SW contacts open by centrifugal device (works fine) on motor shaft. I polished the points but was told that t...

Motor running: source 12.2V,motor 11V,6A inrush, 5A running, motor 2.2 ohms 1 ohm in series (used two 10W in parallel) : inrush 3.7A, run 3.4A, R drop 3.4V, motor 6.5V...Worked as needed...pump a little slow. 2.2 ohms in series (15W): inrush & run same 2.5A,R drop 5.5V, motor drop 4.7V Pump too ...

CHECKING OUT CABLE SIZES, CONNECTORS, START UP INRUSH, DRAW & SHUT DOWN V. CONSIDERING AC RELAY OFF INVERTER TO OPEN PUMP POS. FROM HOUSE BATTERIES WHICH RUN INVERTER; SWITCHING PUMP ONTO MOTOR BAT (ISOLATED FROM HOUSE BAT.) DURING INVERTER USE ... THE SUGGESTED SECOND BATTERY. PHILBA - COULD YO...

A 400 WATTS INVERTER (12 V DC TO 120 V AC, RATED 300 WATTS CONTINUOUS) RUNS A VIDEO & TV UNTIL SOMEONE GETS A GLASS OF WATER. THE TAP (ON A BOAT) TURNS ON A 12 V WATER PUMP... ON OCCASSIONS THE TV FLICKERS THEN CONTINUES ... BUT USUALLY THE INVERTER SHUTS OFF. YES I KNOW THE OBVIOUS NON ELECTRON...

THE ISOLATOR IS DESIGNED TO KEEP THE MOTOR BAT. & HOUSE BATS. SEPARATED. IT CONSISTS OF TWO DIODES WHICH BOTH TEST GOOD (REVERSING OHM METER LEADS GIVES VERY DIFFERENT READINGS) ONE FEEDS THE MOTOR BATTERY THE OTHER THE HOUSE BATS. & V. REG. FEEDS THEM BOTH. THE MOTOR WAS ADVERTISED AS PUTTI...

READINGS WERE TAKEN WITH MOTOR RUNNING BETWEEN BATTERY GROUND AND ISOLATOR INPUT. NO ALTERNATOR, STATTOR OUTPUTS TO V.. REG. TO ISOLATOR. BATTERIES ARE BEING CHARGED.. GUESS ITS A CURIOSITY QUESTION - ONLY A 5 V OUTPUT???? THEN GOING THROUGH THE ISOLATOR (PRESUMABLY JUST DIODES) THE V. JUMPS TO 13.6...

THE V. REG. OUTPUT IS 5 V from my MERC 40 HP outboard. I was expecting 14-16 V. WHY SO LOW?
THE INPUT TO my BATTERY ISOLATOR IS 5 V. THE
OUTPUT IS 13.6 V TO EACH BATTERY. HOW DOES THE VOLTAGE INCREASE ? WHAT HAPPENED TO THE 0.7 V DROP?

MARINE REGULATIONS REQUIRE THE STERN OF MY VESSEL TO BE A MINIMUM OF 100 METRES OFFSHORE WHEN ANCHORING. USING A DINGHY A REFLECTOR COULD BE PLACED AT THE WATER ,S EDGE. BUT PLACING A COUPLE OF REFLECTORS FOR TRANGULATING IS NOT AN OPTION.. ANY DEVICE THAT COULD BE USED FOR SAID DETERMINATION THAT I...

THE RELAY (one only) IS ACTIVATED BY AN ALARM SYSTEM.
RELAY ON (1-2 sec. )
OFF (1-2 sec.)
ON PERMANENTLY

A RELAY NEEDS TO BE ACTIVATED THEN DEACTIVATED FOR 1-2 SEC. THEN ACTIVATED & REMAIN ACTIVATED. THE PULSE CANNOT BE INITIATED BY A MECHANICAL SW (relay is part of an alarm system). A DPDT SW ON THE RELAY IS AVAILABLE AS A PART OF THE PULSING CIRCUIT. IDEALLY THE POWER FOR THE PULSE CIRCUIT WOULD ...

HOW DOES ONE ELECTRONICALLY MAKE A MOMENTARY SW? IN THIS CASE IT MUST BE ACTIVATED WHEN A RELAY SW CLOSES & REMAINS CLOSED. (12 V.)