Thanks for the link to Homeseer.com. That will take a little studying to see if they have something that will do my job. I tend to DIY, and am able to design/build PCB's, have several PIC's and a PLC that manages a 3 fuel standby generator.
Another one is Smarthome.com.
Search found 53 matches
- Sun Apr 11, 2010 11:44 am
- Forum: General Discussion
- Topic: Monitor house current Magazine article Info??
- Replies: 9
- Views: 4793
- Fri Apr 09, 2010 5:14 pm
- Forum: General Discussion
- Topic: Monitor house current Magazine article Info??
- Replies: 9
- Views: 4793
Looking for Circuit Cellar August, September 1996
Looking for copy of Circuit Cellar magazine article by Jeff Baachiochi, August, September 1996. OK to scan and E-mail. Thanks.
- Fri Apr 09, 2010 2:03 pm
- Forum: General Discussion
- Topic: Monitor house current Magazine article Info??
- Replies: 9
- Views: 4793
Monitor house current Magazine article Info??
About 4 years ago, there was an article in either Nuts & Volts or Circuit Cellar magazine that showed how to measure the current (amps) on household electrical circuits. The method was to take say 6 wraps of #18 yellow wire around one circuit's hot wire at the circuit breaker. These pairs of wir...
- Fri Dec 19, 2008 12:31 pm
- Forum: General Discussion
- Topic: The newest registered user is Forrest Mims III
- Replies: 26
- Views: 13426
- Fri Dec 19, 2008 12:25 pm
- Forum: General Discussion
- Topic: Nuts and Bolts
- Replies: 41
- Views: 15359
They are likely to be metric sizes (all or in part). There are several US standard sizes in that size range that the nut fits the other family, and the machine screw won't fit the the nut or visa versa. I have run into that numerous times lately, and when putting spares that I am unsure of back to s...
- Mon Apr 28, 2008 5:37 pm
- Forum: General Discussion
- Topic: COnverting to HDTV
- Replies: 14
- Views: 6368
The component interface, blue/green/etc., does that have the full HDTV, or 4 SDTV or digital content that requires all the bandwidth to require fancy cable? I see component to Cat-5 baluns, do they work? I heard the provide a less than good video. hdmi http://www.mcmelectronics.com/product/33-10450 ...
- Mon Apr 28, 2008 2:41 pm
- Forum: General Discussion
- Topic: COnverting to HDTV
- Replies: 14
- Views: 6368
Was said: signal on RG-6 is analog. I don't know (well out of my expertice), it's different than the old analog, what I was trying to say is I receive HDTV from over the air on the RG-6, therefore it has sufficient bandwidth, or whatever it's called to get a HDTV signal to the receiver. Just like th...
- Mon Apr 28, 2008 1:34 pm
- Forum: General Discussion
- Topic: COnverting to HDTV
- Replies: 14
- Views: 6368
BiggLEz said: You would need a very widebandwidth analog RF channel to carry the 19.4Mbits/sec HD data (that comes out of the HD receiver). My current RG-6 plus combiner/splitter (a dozen coax's to it) does a fine job of delivering HDTV from roof antenna to receivers. Of course that is digital data,...
- Mon Apr 28, 2008 10:56 am
- Forum: General Discussion
- Topic: COnverting to HDTV
- Replies: 14
- Views: 6368
1 TV is full HDTV, 1 is HD monitor (will get a tuner for it), 1 is old analog and it will be repaced with full HDTV in near future, and computer is HDTV. Would like to distribute HD, otherwise my current setup would work. Plan to replace the 2 Directv with HD units in near future. It's just the dist...
- Mon Apr 28, 2008 9:29 am
- Forum: General Discussion
- Topic: COnverting to HDTV
- Replies: 14
- Views: 6368
That unit combines 2 signals to output 8 of them. I would need 2 in parallel to give me 4 inputs, and then that would mean running HDMI cable 2 sets everywhere, some of them 60 foot long, strung from attic down to a wall outlet box, and those cables aren't cheap and are difficult to terminate yourse...
- Mon Apr 28, 2008 5:44 am
- Forum: General Discussion
- Topic: COnverting to HDTV
- Replies: 14
- Views: 6368
COnverting to HDTV
My current setup is a home NTSC distribution network where all the receivers go through modulators so a one goes from one receiver to the other all they have to do is tune that modulator frequency. All the receivers go to a combiner/splitter and then to the receivers. Here's a list of receivers: (2)...
- Sun Jan 20, 2008 11:07 am
- Forum: General Discussion
- Topic: AC transfer switch question
- Replies: 27
- Views: 10661
Hope I didn't offend anyone, was replying as much to other replies to the thread as much as the orignal author. Seemed some were a little new at this area and was concerned with safety. . Keep pushing your electric supplier toward buy back. Only yesterday heard of a power company in the California a...
- Sun Jan 20, 2008 8:01 am
- Forum: General Discussion
- Topic: AC transfer switch question
- Replies: 27
- Views: 10661
Federal Law (USA) REQUIRES that you use an appropriately rated and certified transfer switch. This is to prevent killing a lineman if there is an outage on the electric service. If there is any interconnection possible between your power source, and the electric service, the safety of the line crews...
- Sun Jan 20, 2008 7:32 am
- Forum: General Discussion
- Topic: weird power problem
- Replies: 29
- Views: 13404
Flickering indicates a loose connection, and it could be dirty (damaged) contacts on the breaker. How old is the house, what type wiring does it have, and I'm thinking in the USA standard wiring. If any of the wires are aluminum (and this is a major safety issue!!!) preferably change them to copper,...
- Fri Nov 23, 2007 1:18 pm
- Forum: General Discussion
- Topic: Any magneto ignition experts out there?
- Replies: 5
- Views: 3772