Search found 1330 matches

by Lenp
Mon Jun 17, 2019 7:40 pm
Forum: General Discussion
Topic: Crazy Phone issues here..
Replies: 8
Views: 286

Re: Crazy Phone issues here..

Seen a central office lately?
No relays, clicking, buzzing only the sound of the air handlers.
It's all solid state and when Zeuss visits, it is unfathomable what he can make happen!
Upgrades are often downgrades.
by Lenp
Mon Jun 17, 2019 7:33 pm
Forum: General Discussion
Topic: Ahooga!
Replies: 0
Views: 9

Ahooga!

I was recently involved with a vintage Ahooga horn project for a friend, and it was was a good example of a plan almost not coming together. He wanted the horn to be self-contained in a carrying bag for concealment, and a wireless remote control to sound the horn. To start with, the horn is 6 VDC at...
by Lenp
Fri May 24, 2019 12:19 pm
Forum: General Discussion
Topic: Technology Backfire?
Replies: 38
Views: 1871

Re: Technology Backfire?

Funny story.. I had a friend that had big power lines at the rear of his property. He gathered all the extension cords he could find, hooked them up and laid them down as a coil near the tower base. He couldn't believe that he only read about 1 volt so he had me check his readings. I also read about...
by Lenp
Tue May 14, 2019 12:33 am
Forum: General Discussion
Topic: jack Question
Replies: 3
Views: 237

Re: jack Question

Thanks all, the jack has been found at https://www.tubesandmore.com/products/jack-stereo-14-pc-mount-fender-amps-88-99 The picture is out of proportion but the measurements in the specs are almost the same as the OEM jack. It seems that Fender also uses this jack on some amps, and the only differenc...
by Lenp
Mon May 13, 2019 7:31 pm
Forum: General Discussion
Topic: CNC Router anyone?
Replies: 5
Views: 258

Re: CNC Router anyone?

Yes, I am aware of many CNC forums but I was hoping to attract someone that does work similar to what I am doing. Most of the time I am cutting flat work, like front panels and enclosures for products I produce. Square or rectangular cutouts used to be a royal pain and now it's just draw and cut. Ro...
by Lenp
Sun May 12, 2019 12:51 pm
Forum: General Discussion
Topic: jack Question
Replies: 3
Views: 237

jack Question

I have a Pyle portable amplifier in for service, with a couple of the front panerl 1/4" jacks broken. They are 1/4" TRS (Stereo) jacks, but they have two isolated switches. They have 7 terminals, Sw1, Sw2, T, R, S and it is board with a threaded barrel. The jack body measures 27mm long. 17.5 mm wide...
by Lenp
Thu May 09, 2019 11:17 pm
Forum: General Discussion
Topic: Bud Metal Question!
Replies: 5
Views: 237

Re: Bud Metal Question!

Years ago I struggled to repair a water spot on a piece of furniture. The more I worked, the worse it got. I caller MinWax tech support and they helped make it disappear. First, don't sand just the area, make a bigger area the repair so it blends gradually. Next don't use fine sand paper first. It b...
by Lenp
Thu May 02, 2019 7:47 pm
Forum: General Discussion
Topic: CNC Router anyone?
Replies: 5
Views: 258

CNC Router anyone?

Just a shout out to see if anyone in this dwindling forum is doing any CNC fabrication with a table top router. I've had mine up for about a year and have had pretty fair success cutting plastic and aluminum panels and enclosures. I would like to compare notes and discuss modifications I've done and...
by Lenp
Thu May 02, 2019 7:35 pm
Forum: General Discussion
Topic: Technology Backfire?
Replies: 38
Views: 1871

Re: Technology Backfire?

I wound a 4 foot 1,000,000 turn coil of wire on the roof and hooked up a diode to charge the battery. It kinda works but the car turns left ok but its cranky on right ones. The GPS brings me back to where I started from in 23 hrs, 56 minutes and 4 seconds, the left turn signal is a bit faster than t...
by Lenp
Tue Apr 30, 2019 8:45 pm
Forum: General Discussion
Topic: TV lacking remote control...
Replies: 13
Views: 1071

Re: TV lacking remote control...

My shop set is a Vizio smart set and it would turn on from the remote but no other remote buttons worked, and only unplugging it turned it off. The remote was swapped with another proven remote with the same result. I found a power and main board set online for around $30. Swapped them out with the ...
by Lenp
Mon Apr 29, 2019 8:43 am
Forum: General Discussion
Topic: Bud Metal Question!
Replies: 5
Views: 237

Re: Bud Metal Question!

Most of the dings are on the back of the cabinet
where a fan cutout is milled. The front has a lot of machining but that is covered with a graphic overlay.so it is clean.
Since this is a product being sold I just want to cover the bare metal showing through.
by Lenp
Sun Apr 28, 2019 11:21 pm
Forum: General Discussion
Topic: Technology Backfire?
Replies: 38
Views: 1871

Re: Technology Backfire?

Right now the Honda has been behaving itself, but, we use it more frequently than we did at first. Now that the weather is getting better for those outside tasks, I will plan to get a list of the phantom load circuits and we'll see if that helps unravel this issue. I understand from a friend that at...
by Lenp
Sun Apr 28, 2019 11:01 pm
Forum: General Discussion
Topic: Bud Metal Question!
Replies: 5
Views: 237

Bud Metal Question!

I am looking for a source of touch-up paint for Bud Metals line of PortaCab enclosures. I think it is a common light gray color that is used on many of their products. Some of the many PortaCab enclosures I use, from time to time mysteriously develop 'shop rash'; manifesting as a ding or two. I cont...
by Lenp
Sun Apr 28, 2019 10:21 pm
Forum: General Discussion
Topic: Death Rattle?
Replies: 8
Views: 866

Re: Death Rattle?

Well, that's a positive step in the right direction!
Thanks Sean
by Lenp
Tue Apr 23, 2019 6:32 pm
Forum: General Discussion
Topic: Death Rattle?
Replies: 8
Views: 866

Death Rattle?

I just spent considerabe time on the Nuts & Volts magazine site. It is no wonder we are dying, there is NO obvious mention of this forum. There are loads of links to the magazine articles and their print 'tech forum' I went there because someone I mentioned this forum to could not find us, and I als...