hi
thanks guys , i found a place that carries 28c64's and they will be fine for my project , i was hoping some parts place still carried the 28f64's , thanks again , dana
Search found 24 matches
- Sun Dec 10, 2006 4:01 pm
- Forum: General Discussion
- Topic: source for 28f64 flash rams?
- Replies: 3
- Views: 2293
- Sat Dec 09, 2006 5:07 pm
- Forum: General Discussion
- Topic: source for 28f64 flash rams?
- Replies: 3
- Views: 2293
source for 28f64 flash rams?
hi
i am building a SBC and want to use an 8K x 8 flash ram , does anyone know where i can find a source for these chips thanks , dana
i am building a SBC and want to use an 8K x 8 flash ram , does anyone know where i can find a source for these chips thanks , dana
- Thu Aug 17, 2006 9:03 am
- Forum: General Discussion
- Topic: USB DEVICE CONTROL in NUT&VOLTS by A.Enzmann
- Replies: 33
- Views: 18869
- Thu Aug 17, 2006 5:03 am
- Forum: General Discussion
- Topic: USB DEVICE CONTROL in NUT&VOLTS by A.Enzmann
- Replies: 33
- Views: 18869
hi sorry i didn't see your posts sooner , i have had basically the same problems , i can get the hex file listed to run the chip fine but although i can get the source file to compile , the produced hex file comes out a different size and then doesn't run , i have been hoping A.Enzmann would see thi...
- Tue Jun 13, 2006 3:54 am
- Forum: General Discussion
- Topic: Board Manufactures
- Replies: 16
- Views: 8515
hi i've been useing ExpressPCB and really like it , the boards are great and the turn around is good , the other thing they let you do , that some of the other companies wont is , you can make multiple copies of a small board so say your three mini boards will cut up into 12 smaller boards :grin: th...
- Tue Jun 06, 2006 6:31 pm
- Forum: General Discussion
- Topic: USB DEVICE CONTROL in NUT&VOLTS by A.Enzmann
- Replies: 33
- Views: 18869
hi setec yes i was busy trying that and getting nowhere :sad: , and posted on another forum and come to find out i have the lastest (official) release of sdcc >02.5.0< and it doesn't support the 18f2455 , for that you need whats called the daily snapshot :???: the latest snapshot is version 02.5.6 j...
- Tue Jun 06, 2006 8:28 am
- Forum: Computer Programming
- Topic: trouble with n&v article (USB DEVICE CONTROL) and SDCC
- Replies: 2
- Views: 3679
- Tue Jun 06, 2006 6:22 am
- Forum: Computer Programming
- Topic: trouble with n&v article (USB DEVICE CONTROL) and SDCC
- Replies: 2
- Views: 3679
trouble with n&v article (USB DEVICE CONTROL) and SDCC
hi i have been working on the project from the n&v article USB DEVICE CONTROL and have the hex file loaded and working but i downloaded SDCC and GPUTILS and have them installed on an XP system and cannot get SDCC to compile the main.c program from the article , any help would be great :grin: , d...
- Tue Jun 06, 2006 5:11 am
- Forum: General Discussion
- Topic: USB DEVICE CONTROL in NUT&VOLTS by A.Enzmann
- Replies: 33
- Views: 18869
hi i was able to get the supplied hex file working without too much trouble , just me chugging up the learning curve :???: :smile: , but i realized i want to compile the main.c file and get it so i can edit it to work , from the article he seems to be useing SDCC and GPUTILS and i went to sourceforg...
- Tue Jun 06, 2006 5:03 am
- Forum: General Discussion
- Topic: help installing gputils on an XP system
- Replies: 1
- Views: 1740
- Tue Jun 06, 2006 4:01 am
- Forum: General Discussion
- Topic: help installing gputils on an XP system
- Replies: 1
- Views: 1740
help installing gputils on an XP system
hi i am trying to work with a "C" program and get it compiled and converted to a hex file so i can load it into a pic chip , i downloaded SDCC and GPUTILS and have SDCC working fine but getting GPUTILS to load on a XP system is beyond me :???: , it is setup for a linux system and i underst...
- Mon Jun 05, 2006 12:56 pm
- Forum: General Discussion
- Topic: USB DEVICE CONTROL in NUT&VOLTS by A.Enzmann
- Replies: 33
- Views: 18869
hi thanks , i just checked it out and see a thread for USBCNC , most of the small CNC machines run off the printer port , and USB seems to be the new trend , USB has been beyond most people at the hobbiest level ( me :grin: ) and with the new pic's the door is starting to open , the USBCNC is design...
- Mon Jun 05, 2006 9:35 am
- Forum: General Discussion
- Topic: USB DEVICE CONTROL in NUT&VOLTS by A.Enzmann
- Replies: 33
- Views: 18869
hi i have been interfacing with the parallel port for years and now that USB is the standard port i want to be able to use it instead i have a plasma CNC cutter i built and a 3D room scanner and various micro controller projects and have used the EPP port on my system , so for instance with my plasm...
- Sun Jun 04, 2006 1:30 pm
- Forum: General Discussion
- Topic: PIC Programmer for Linux Laptop
- Replies: 7
- Views: 3912
hi i just got a olimex ( pic-mcp-usb ) programmer from sparkfun for $87.00 http://www.sparkfun.com/commerce/product_info.php?products_id=4 i thought it was a good setup as it doesn't need an external power supply and it comes with the ZIF socket the usb it has is a built in usb-serial , don't know a...
- Sat Jun 03, 2006 1:32 pm
- Forum: General Discussion
- Topic: Is Radio Shack making or losing money?
- Replies: 15
- Views: 8598