Robert, I have my ststem behind smoked glass & I have not noticed any degredation in operation of IR.
Go for it
Mike M
Search found 22 matches
- Sun Dec 18, 2005 9:53 pm
- Forum: General Discussion
- Topic: IR thru glass
- Replies: 9
- Views: 3832
- Thu Sep 22, 2005 10:10 pm
- Forum: General Discussion
- Topic: Green Laser pen
- Replies: 71
- Views: 27937
Re: Green Laser pen
Aint this just more PHUN than a barrel of monekys.<p>Chris your right,this is the worest goverment there is accept for all the rest.<p>The system is broken because it was never designed to handel this many stupid people.
- Fri Jul 08, 2005 10:50 pm
- Forum: General Discussion
- Topic: Steam power?
- Replies: 12
- Views: 5957
Re: Steam power?
Ya just cant beat the sence of acompleshment when you carve anything like that out of billit material.<p>If you need help with any machining let me know.<p>some neet stuff at this site.
http://www.homestead.com/tool20895/CABIN2002.html<p>MIKE M
http://www.homestead.com/tool20895/CABIN2002.html<p>MIKE M
- Fri Jul 08, 2005 10:08 pm
- Forum: General Discussion
- Topic: did you get July Issue?
- Replies: 4
- Views: 2606
Re: did you get July Issue?
Mike, I received 2 copies of july issue,maby they sent me your copy by mistake.<p>
(only joking,did receive 2 copies and saw your add in both, maby i can use your service some day .<p>
Have WRANGLER RUBICON ,NO NEED LAND ROVER.<p>MIKE M
(only joking,did receive 2 copies and saw your add in both, maby i can use your service some day .<p>
Have WRANGLER RUBICON ,NO NEED LAND ROVER.<p>MIKE M
- Wed Jun 29, 2005 9:14 pm
- Forum: General Discussion
- Topic: down dirty inverter advice needed
- Replies: 43
- Views: 13909
Re: down dirty inverter advice needed
Hi Chris, sounds like you have alot of experience with floresenc lights.<p>I have about 40 of the 2bulb 8 footers hanging in my shop.(I forget the wattage at time of writing)<p>Question is. is ther any inexpensive way to get more light output from them, as in buy or make to replace the existing ball...
- Mon Jun 13, 2005 9:10 pm
- Forum: General Discussion
- Topic: Event Per Hour
- Replies: 7
- Views: 4211
Event Per Hour
What I need is a circuit that will read a button pushed and display a rate (button pushes/hour) in rear time.<p>The range would be 1/hr to 360/hr.<p>does anyone know of any existing device that can be adapted. Or would it be so special that a design your own is the only way.<p>If design your own is ...
- Thu Jun 02, 2005 8:46 pm
- Forum: General Discussion
- Topic: bandsaw blade welder (old one)
- Replies: 26
- Views: 12920
Re: bandsaw blade welder (old one)
Crowbar, did you have any luck finding a schematic for stryco welder.<p>Much apprication<p>Mike M
- Tue May 31, 2005 9:15 pm
- Forum: General Discussion
- Topic: Simple presence detector help?
- Replies: 6
- Views: 3693
Re: Simple presence detector help?
Would motion detecter work to sense presence?<p>That type of detecter is low cost,and should be easy
to interface with motor on circuit.
to interface with motor on circuit.
- Mon May 23, 2005 8:33 pm
- Forum: General Discussion
- Topic: ian's grammactical rules
- Replies: 48
- Views: 19443
Re: ian's grammactical rules
To much gas,it's going to blow.
- Mon May 23, 2005 8:29 pm
- Forum: General Discussion
- Topic: ian's grammactical rules
- Replies: 48
- Views: 19443
Re: ian's grammactical rules
To much gas,it's going to blow.
- Wed May 18, 2005 10:42 pm
- Forum: General Discussion
- Topic: bandsaw blade welder (old one)
- Replies: 26
- Views: 12920
Re: bandsaw blade welder (old one)
The transformer that looks like it is part of welder reads .75 KVA. It has 4 different wireing combinations (high voltage, low voltage) single phase.<p>The wire diagram says (line),my source is 208V, 3ph If I take any 2 legs of 208V, 3PH then I have 208V, 1PH. Connect 208V,1PH to line of transformer...
- Wed May 18, 2005 10:01 pm
- Forum: General Discussion
- Topic: WATT-HOUR METER Table Lamp
- Replies: 7
- Views: 3658
Re: WATT-HOUR METER Table Lamp
Connect a small motor to the thing that spins .
- Mon May 16, 2005 8:12 pm
- Forum: General Discussion
- Topic: National Debt
- Replies: 13
- Views: 5406
Re: National Debt
I paid in 97,they didnt think it was enough so im still paying for 97,<p>only
because they have more guns
because they have more guns
- Fri May 13, 2005 4:18 pm
- Forum: General Discussion
- Topic: bandsaw blade welder (old one)
- Replies: 26
- Views: 12920
Re: bandsaw blade welder (old one)
How does this sound, I will build a recitifier able to deliver somewhere between 250 to 450 amps at say 2 to 10 volts. This should weld those ends togather.<p>Any ideas on the cheapest & easy way to do this.<p>full wave bridge half wave bridge<p>You can cut an orange with a 2x4 but why not use a...
- Tue May 10, 2005 9:06 pm
- Forum: General Discussion
- Topic: bandsaw blade welder (old one)
- Replies: 26
- Views: 12920
Re: bandsaw blade welder (old one)
Larry ,thanks for the tips on blade welding.<p>What Im looking for right now is a schematic for the same exact type or similar blade welder so I can get this one working.<p>This one is missing power supply.<p>I was thinking if i could find a schematic i build the thing.<p>thanks Mike M