Search found 22 matches

by 2M MACHINING
Sun Dec 18, 2005 9:53 pm
Forum: General Discussion
Topic: IR thru glass
Replies: 9
Views: 3794

Re: IR thru glass

Robert, I have my ststem behind smoked glass & I have not noticed any degredation in operation of IR.
Go for it
Mike M
by 2M MACHINING
Thu Sep 22, 2005 10:10 pm
Forum: General Discussion
Topic: Green Laser pen
Replies: 71
Views: 27704

Re: Green Laser pen

Aint this just more PHUN than a barrel of monekys.<p>Chris your right,this is the worest goverment there is accept for all the rest.<p>The system is broken because it was never designed to handel this many stupid people.
by 2M MACHINING
Fri Jul 08, 2005 10:50 pm
Forum: General Discussion
Topic: Steam power?
Replies: 12
Views: 5875

Re: Steam power?

Ya just cant beat the sence of acompleshment when you carve anything like that out of billit material.<p>If you need help with any machining let me know.<p>some neet stuff at this site.
http://www.homestead.com/tool20895/CABIN2002.html<p>MIKE M
by 2M MACHINING
Fri Jul 08, 2005 10:08 pm
Forum: General Discussion
Topic: did you get July Issue?
Replies: 4
Views: 2588

Re: did you get July Issue?

Mike, I received 2 copies of july issue,maby they sent me your copy by mistake.<p>
(only joking,did receive 2 copies and saw your add in both, maby i can use your service some day :) .<p>
Have WRANGLER RUBICON ,NO NEED LAND ROVER.<p>MIKE M
by 2M MACHINING
Wed Jun 29, 2005 9:14 pm
Forum: General Discussion
Topic: down dirty inverter advice needed
Replies: 43
Views: 13834

Re: down dirty inverter advice needed

Hi Chris, sounds like you have alot of experience with floresenc lights.<p>I have about 40 of the 2bulb 8 footers hanging in my shop.(I forget the wattage at time of writing)<p>Question is. is ther any inexpensive way to get more light output from them, as in buy or make to replace the existing ball...
by 2M MACHINING
Mon Jun 13, 2005 9:10 pm
Forum: General Discussion
Topic: Event Per Hour
Replies: 7
Views: 4166

Event Per Hour

What I need is a circuit that will read a button pushed and display a rate (button pushes/hour) in rear time.<p>The range would be 1/hr to 360/hr.<p>does anyone know of any existing device that can be adapted. Or would it be so special that a design your own is the only way.<p>If design your own is ...
by 2M MACHINING
Thu Jun 02, 2005 8:46 pm
Forum: General Discussion
Topic: bandsaw blade welder (old one)
Replies: 26
Views: 12792

Re: bandsaw blade welder (old one)

Crowbar, did you have any luck finding a schematic for stryco welder.<p>Much apprication<p>Mike M
by 2M MACHINING
Tue May 31, 2005 9:15 pm
Forum: General Discussion
Topic: Simple presence detector help?
Replies: 6
Views: 3657

Re: Simple presence detector help?

Would motion detecter work to sense presence?<p>That type of detecter is low cost,and should be easy
to interface with motor on circuit.
by 2M MACHINING
Mon May 23, 2005 8:33 pm
Forum: General Discussion
Topic: ian's grammactical rules
Replies: 48
Views: 19177

Re: ian's grammactical rules

To much gas,it's going to blow.
by 2M MACHINING
Mon May 23, 2005 8:29 pm
Forum: General Discussion
Topic: ian's grammactical rules
Replies: 48
Views: 19177

Re: ian's grammactical rules

To much gas,it's going to blow.
by 2M MACHINING
Wed May 18, 2005 10:42 pm
Forum: General Discussion
Topic: bandsaw blade welder (old one)
Replies: 26
Views: 12792

Re: bandsaw blade welder (old one)

The transformer that looks like it is part of welder reads .75 KVA. It has 4 different wireing combinations (high voltage, low voltage) single phase.<p>The wire diagram says (line),my source is 208V, 3ph If I take any 2 legs of 208V, 3PH then I have 208V, 1PH. Connect 208V,1PH to line of transformer...
by 2M MACHINING
Wed May 18, 2005 10:01 pm
Forum: General Discussion
Topic: WATT-HOUR METER Table Lamp
Replies: 7
Views: 3622

Re: WATT-HOUR METER Table Lamp

Connect a small motor to the thing that spins .
by 2M MACHINING
Mon May 16, 2005 8:12 pm
Forum: General Discussion
Topic: National Debt
Replies: 13
Views: 5337

Re: National Debt

I paid in 97,they didnt think it was enough so im still paying for 97,<p>only
because they have more guns
by 2M MACHINING
Fri May 13, 2005 4:18 pm
Forum: General Discussion
Topic: bandsaw blade welder (old one)
Replies: 26
Views: 12792

Re: bandsaw blade welder (old one)

How does this sound, I will build a recitifier able to deliver somewhere between 250 to 450 amps at say 2 to 10 volts. This should weld those ends togather.<p>Any ideas on the cheapest & easy way to do this.<p>full wave bridge half wave bridge<p>You can cut an orange with a 2x4 but why not use a...
by 2M MACHINING
Tue May 10, 2005 9:06 pm
Forum: General Discussion
Topic: bandsaw blade welder (old one)
Replies: 26
Views: 12792

Re: bandsaw blade welder (old one)

Larry ,thanks for the tips on blade welding.<p>What Im looking for right now is a schematic for the same exact type or similar blade welder so I can get this one working.<p>This one is missing power supply.<p>I was thinking if i could find a schematic i build the thing.<p>thanks Mike M