Search found 9 matches

by flinchy69
Tue Feb 15, 2011 7:44 pm
Forum: General Discussion
Topic: whitfield pellet stove
Replies: 55
Views: 28142

Re: whitfield pellet stove

give me ref designater and I'll give you the value
by flinchy69
Fri Oct 09, 2009 8:49 pm
Forum: General Discussion
Topic: Crimping connector contacts
Replies: 10
Views: 2067

Re: Crimping connector contacts

This is a cheapy: http://www.radioshack.com/product/index ... Id=2103683 but I use this on my pinball machines with pretty good results just gotta go slow and steady, not good for a production environment
by flinchy69
Wed Sep 23, 2009 6:51 pm
Forum: General Discussion
Topic: whitfield pellet stove
Replies: 55
Views: 28142

Re: whitfield pellet stove

Ok so I took the module that I xrayed and made some measurements. I then did a little careful coring as to not damage circuit any more then needed to get the remainder of the info that I wasn't able to get with the bare board. http://i596.photobucket.com/albums/tt44/flinchy69/50kmodule0002.jpg?t=125...
by flinchy69
Tue Sep 22, 2009 6:19 pm
Forum: General Discussion
Topic: whitfield pellet stove
Replies: 55
Views: 28142

Re: whitfield pellet stove

Ok here it is: http://i596.photobucket.com/albums/tt44/flinchy69/whitfieldcontrol005.jpg?t=1253671540 the 2 resistors to the diodes are 100 ohms ea. The resistor between grey and pinkish purple measure ~1.3 meg. All others ????????? pins are #'ed 1 -10 left to right. #1 is pin2 of triac externally #...
by flinchy69
Tue Sep 22, 2009 5:39 pm
Forum: General Discussion
Topic: whitfield pellet stove
Replies: 55
Views: 28142

Re: whitfield pellet stove

Yup , right after writing last post I verified I was wrong. the trick to measuring is to not push hard with the probes or I punch through. Unfortunatly most of them are damaged from the dremel when I removed epoxy so it will have to be a guess I think. But I have values for a couple.
by flinchy69
Tue Sep 22, 2009 3:32 pm
Forum: General Discussion
Topic: whitfield pellet stove
Replies: 55
Views: 28142

Re: whitfield pellet stove

There isn't a resistor one on this board. I think your mistaking black marks as resistors. My thought is that they were used to line up pick and place machine when it was populated. There is no continuity across those points at all. If i'm wrong I'd love to have some light shed on it. I have the mai...
by flinchy69
Tue Sep 22, 2009 8:49 am
Forum: General Discussion
Topic: whitfield pellet stove
Replies: 55
Views: 28142

Re: whitfield pellet stove

If I told you I'd have to kill you....... Lol seriously we use them where I work as a lowie(sp?) to exammine crystal planes. But got permissin to throw this in for a quick look. It would be hard to do point to point without exposing circuit like I have,but this gives you an idea. I am in the process...
by flinchy69
Mon Sep 21, 2009 9:45 pm
Forum: General Discussion
Topic: whitfield pellet stove
Replies: 55
Views: 28142

Re: whitfield pellet stove

i know this topic is way old and posts are straying away from original question, but in an effort to keep this thread going in a positive direction and keep these old stoves off the scrap heap let me add a little info to take some of the mystery out of the proprietary "ic's" I've grinded one down to...
by flinchy69
Mon Sep 21, 2009 9:24 pm
Forum: General Discussion
Topic: Whitfield Pellet Stove
Replies: 15
Views: 3638

Re: Whitfield Pellet Stove

Two clues original poster gives here. #1 Lights blinking #2 fan speed slows to about #1 setting. This is the a normal state that stove reverts to when thermostat goes above set point. ( a low standby mode until room cools down below set point). There are 2 spade terms jumped together when stove is u...