Just finished the active controls guitar build project in the October issue (HotRod your electric guitar...), and have been experiencing some problems...
It seems to work ok in general, but when the guitar strings are played hard/loud,, the circuit output fades as if over driven and 'squelched', returning in 1/2 second or so... sometimes accompanied by pops and clicks at the start of the fade...
I put a scope on the front end being driven from the guitar pickups, which are delivering up to +/- 1 V max when strummed hard/loud.. which seems high for an opamps input... ??
The TL072 opamp specs reference a Vio of 10mv, so wondering if the 1v input is the problem, and then what to do to correct it... perhaps a voltage splitter across the input??
Any ideas would be greatly appreciated.. I need to get this guitar back in operation for a buddy
-thx
-Dr. Obscure
Some help with guitar active controls OpAmp circuit
-
- Posts: 9
- Joined: Sat Feb 15, 2014 6:35 pm
- Contact:
Re: Some help with guitar active controls OpAmp circuit
I've read the article and seen the schematic. One volt input should not be a problem, in fact the maximum input is limited to the supply voltage which in this case is + and - 9 volts. The design seems to be able to handle a 1 volt input with out clipping at full boost. I suppose I would check the batteries first then double check the wiring at this point.
Steve G
Steve G
-
- Posts: 9
- Joined: Sat Feb 15, 2014 6:35 pm
- Contact:
Re: Some help with guitar active controls OpAmp circuit
Thanks for the reply Steve...
The batteries are new, and verified.. the circuit works ok with low input, but cuts out a the 1v pp area...
If it was clipping would I expect to hear serious distortion, as opposed to a complete fade/loss of output?
I'll throw the guitar back up on the bench tomorrow and see what the output shows on the fade -- clipped or reduced waveforms..
Thanks again,
-chane
The batteries are new, and verified.. the circuit works ok with low input, but cuts out a the 1v pp area...
If it was clipping would I expect to hear serious distortion, as opposed to a complete fade/loss of output?
I'll throw the guitar back up on the bench tomorrow and see what the output shows on the fade -- clipped or reduced waveforms..
Thanks again,
-chane
Re: Some help with guitar active controls OpAmp circuit
Yes you would. Something else to consider, does it cut out regardless of where the controls are set? From the circuit description the gain is flat with the controls at midpoint. Should easily handle a 1 volt signal.If it was clipping would I expect to hear serious distortion, as opposed to a complete fade/loss of output?
Steve G.
-
- Posts: 9
- Joined: Sat Feb 15, 2014 6:35 pm
- Contact:
Re: Some help with guitar active controls OpAmp circuit
Steve happy to report the issue has been resolved...
To answer your queries, yes it was happening regardless of control settings, or which set of pickups was engaged, etc.. was all very perplexing..
Anyway, in the process of setting things up on the test bench, I used a signal generator (so I wouldn't have to pluck the strings and traced with the Oscope.. somewhere in that manipulation and moving a part of two for access with the probe, the problem went away.. all the solder joints look good (all glossy, no obvious cold joints) so I'm assuming one of the components, likely a capacitor, was touching something it shouldn't, and caused the failure.. this is a small perf board assembly, stuffed into an area it was never designed for, and this is expected at times
Thanks again for your interest and help with my problem... opamps have always been my nemesis.. someday..
To answer your queries, yes it was happening regardless of control settings, or which set of pickups was engaged, etc.. was all very perplexing..
Anyway, in the process of setting things up on the test bench, I used a signal generator (so I wouldn't have to pluck the strings and traced with the Oscope.. somewhere in that manipulation and moving a part of two for access with the probe, the problem went away.. all the solder joints look good (all glossy, no obvious cold joints) so I'm assuming one of the components, likely a capacitor, was touching something it shouldn't, and caused the failure.. this is a small perf board assembly, stuffed into an area it was never designed for, and this is expected at times
Thanks again for your interest and help with my problem... opamps have always been my nemesis.. someday..
Re: Some help with guitar active controls OpAmp circuit
Your welcome, glad you found the problem
Steve G.
Steve G.
Who is online
Users browsing this forum: No registered users and 5 guests