Search found 373 matches
- Fri Jun 04, 2010 10:43 am
- Forum: General Discussion
- Topic: Temperature reader from different rooms.
- Replies: 9
- Views: 5189
Re: Temperature reader from different rooms.
Take a peek at these: http://para.maxim-ic.com/en/search.mvp?fam=temp_sens&374=1-Wire&374=1-Wire%20Non-Network&tree=master The 1820 series are used widely with hobbyists so there are alot of sample projects out there on the net. You need 2 wires going to each sensor (1 data/power wire an...
- Sun May 30, 2010 7:21 pm
- Forum: General Discussion
- Topic: Adhesive spray
- Replies: 7
- Views: 3277
Re: Adhesive spray
Well, I will have to do some tests. I was hoping someone had done this before and could tell me an exact product that works well and is safe to use.
Kevin
Kevin
- Fri May 28, 2010 11:10 pm
- Forum: General Discussion
- Topic: Adhesive spray
- Replies: 7
- Views: 3277
Adhesive spray
I need to replace the touchscreen of my son's LG CU920. I watched a pair of videos on youtube and the guy referred to some 3m adhesive spray for putting the new module on the front bezel of the phone. Anyone done this before and if so, which particular spray did/do you use? I would prefer to get it ...
- Tue May 25, 2010 6:24 pm
- Forum: General Discussion
- Topic: Soldering irons, stations, Ungar still in business
- Replies: 12
- Views: 8306
Re: Soldering irons, stations, Ungar still in business
I haven't *tried* it but I would bet the ones for the station2A (link above) would work. Circuit Specialists, which I also got a nice hot air rework station from, says they are OEM manu'd specifically for them but I would bet that the design itself is very close to, if not the same exact thing as th...
- Mon May 24, 2010 8:48 pm
- Forum: General Discussion
- Topic: Soldering irons, stations, Ungar still in business
- Replies: 12
- Views: 8306
Re: Soldering irons, stations, Ungar still in business
You mentioned that you might get a station, too. Check out these: http://www.circuitspecialists.com/level.itml/icOid/6388 Especially this one: http://www.circuitspecialists.com/prod.itml/icOid/7508 I have the one above and I love it. I have had it for several years and I have never had a problem wit...
- Wed May 12, 2010 5:32 pm
- Forum: Up For Grabs
- Topic: HughesNet System....Long Gone
- Replies: 8
- Views: 7441
Re: HughesNet System
For anyone else unfortunate enough to have Hughesnet, contact you congressman & state rep. This is what I sent to mine: ----------------------------- I am probably wasting my time (as I have been for the past 10 years), but, I have asked everyone else so I'll ask you. In our area, the only high-...
- Wed May 12, 2010 3:09 pm
- Forum: General Discussion
- Topic: Custom Electronics Service ?
- Replies: 4
- Views: 2557
Re: Custom Electronics Service ?
To answer your main question, you might try looking for a local ham radio operator. Most of them (esp. the old timers) know quite a bit about electronics. If I knew where you are from, I would look. You might look in your phone book for places that sell radio equipment (for ham radio) - tho there pr...
- Sat May 08, 2010 12:31 am
- Forum: General Discussion
- Topic: need a -5 volt supply
- Replies: 4
- Views: 17738
Re: need a -5 volt supply
An LM7905 will give you -5v @ 1amp
- Fri May 07, 2010 9:07 am
- Forum: General Discussion
- Topic: Transfering program to another chip.
- Replies: 16
- Views: 8452
Re: Transfering program to another chip.
I don't use the same programmer but if you can read the hex data, the software *should* allow you to save it as a hex file. Once you have a hex file (with the config data, too), you just program the new chip with the hex file. When you write a program for a PIC, the final output of the compiler/asse...
- Thu May 06, 2010 7:05 pm
- Forum: General Discussion
- Topic: Transfering program to another chip.
- Replies: 16
- Views: 8452
Re: Transfering program to another chip.
If the chip was not programmed with the protection config bits set, you should be able to read the code (including the config bits - they DO matter) then take the hex file and program it to another chip without any problem. I am pretty sure the 84 uses ICSP for programming and if it does, you only n...
- Tue May 04, 2010 10:19 am
- Forum: Computer Programming
- Topic: BoostC
- Replies: 7
- Views: 8120
Re: BoostC
I used MikroPascal for a long time and I didn't run into any major bugs. They do frequent updates. I still have their pascal compiler and I use it (but not very often).
Kevin
Kevin
- Tue Apr 27, 2010 6:32 pm
- Forum: General Discussion
- Topic: Funky Pot Problem
- Replies: 12
- Views: 4343
Re: Funky Pot Problem
Well, I had to order parts for another project (tactile buttons for our oven's control board). I ordered up a couple pot's, too and the whole racing wheel/pedals project works great! I am more than happy with the way it turned out and I wanted to update you all and say thanks again for your input!
- Tue Apr 27, 2010 6:09 pm
- Forum: Projects & Kits
- Topic: Smileys Workshop
- Replies: 9
- Views: 19047
Re: Smileys Workshop
I don't remember what he wrote but to create a button, in the IDE, choose "Button" in the toolbox. Then you can set all of the properties of your new button and play a little (I use VC++ 2008 express)
- Fri Apr 23, 2010 12:45 pm
- Forum: General Discussion
- Topic: Where to get Transparent Paper ?
- Replies: 11
- Views: 6418
Re: Where to get Transparent Paper ?
I use the toner transfer method and it works mostly but not good enough for very small traces. I would love to try the transparency/light box method but, like you, the cost of startup is kinda prohibitive. Let me know how it works out for you!
Kevin
Kevin
- Mon Apr 05, 2010 5:53 pm
- Forum: General Discussion
- Topic: High speed video
- Replies: 6
- Views: 2892
Re: High speed video
-- edit SETEC: You and I posted at the same time... -- Wouldn't a high speed camera (like the ones used on mythbusters) catch the frame as it was being drawn so you could see the progression of the scanning of the beam? They can trace a bullet with those things... I have seen one film of a water bal...