Search found 23 matches
- Wed Jul 02, 2014 10:15 am
- Forum: Computer Programming
- Topic: Interpreting error messages.
- Replies: 1
- Views: 5216
Interpreting error messages.
smile: Hi! I was wondering if it would be possible to have an error section on this forum. If I got an error message on an Ardunio project and I did not understand it I would like to learn the terminology of any error messages so I can understand it and be able to correct my error. Thanks Frank fg
- Thu May 08, 2014 5:46 pm
- Forum: Computer Programming
- Topic: Is it possible to pigyback three programs on the Ardunio?
- Replies: 4
- Views: 7227
Is it possible to pigyback three programs on the Ardunio?
Hi!
I would like to have three programs runing on the Ardunio one after the other or one at a time, in different order.
Is that possible?
Thanks new to programing.
Frank G.
- Thu May 08, 2014 12:18 pm
- Forum: Nuts & Volts Magazine Discussions
- Topic: Ardunio Class 101 chapter 5, Set an Angle on servo
- Replies: 0
- Views: 23812
Ardunio Class 101 chapter 5, Set an Angle on servo
:sad: Hi! Love your articles on Ardunio. I did all the Labs 1,2,&3. Lab 3 however did not do so while. I used a Laptop to do the labs, Setting an angle on a servomotor did not do go. At first it went to 180 degrees, then I typed several degrees points such as 45,90,180. and so on, from the seria...
- Mon Aug 25, 2008 9:51 am
- Forum: Computer Programming
- Topic: No Flow Chart
- Replies: 4
- Views: 3787
- Mon Aug 25, 2008 9:44 am
- Forum: Computer Programming
- Topic: No Flow Chart
- Replies: 4
- Views: 3787
:smile: Hi! Al The slave program was not set up to stop the motors. But it was set up to control the speed via A/D converter using the master keypad. such as 010 to slow it down to its lowest speed or 248 to go faster. The idea is to rewrite the slave program so it would take the three 'ooo' charact...
- Sat Aug 23, 2008 1:12 pm
- Forum: Computer Programming
- Topic: No Flow Chart
- Replies: 4
- Views: 3787
No Flow Chart
:smile: Hi! Al I been out on an unexpected vaction, but I'm back now, ready to get with it. My first objective is to capture the three '000' zero characters fron RS-232 receiver rcreg. from the slave PIC16F88. As explained above, the Master will send the speed control value to the Slave. The way it ...
- Fri Aug 22, 2008 9:58 am
- Forum: Computer Programming
- Topic: No Flow Chart
- Replies: 0
- Views: 2491
No Flow Chart
:smile: Al Sorry I'v been in an unexpected vacation, but I'm back now and ready to go. Master PIC talking to Slave PIC to control a motor. As I said above comunication is good. I need to capture the three zero characters that are being sent to the Masters LCD display from the slave. RS-232 Testip: b...
- Thu Jul 17, 2008 7:46 pm
- Forum: Computer Programming
- Topic: No Flow chat.
- Replies: 2
- Views: 3521
No flow chart.
:smile: NO FLOW CHART Hi! Could use some help in a program that I wrote from a programming course on how to remotely control a D.C. motor. Sorry this is going to be a little lengthily. The programs work except that I want to modify them to suit my purpose. And that were the problem starts. There is ...
- Wed Jul 16, 2008 7:47 am
- Forum: Computer Programming
- Topic: No Flow chat.
- Replies: 2
- Views: 3521
No Flow chat.
Hi!
I am having probels with uploading Word.
I have tryed four tiomes.
Can you help me
thanks
Frank G.
- Thu Jul 10, 2008 8:46 am
- Forum: General Discussion
- Topic: 555 Timer triggered fropm a differentiator.
- Replies: 31
- Views: 19295
- Wed Jul 09, 2008 1:31 pm
- Forum: General Discussion
- Topic: 555 Timer triggered fropm a differentiator.
- Replies: 31
- Views: 19295
- Wed Jul 09, 2008 9:45 am
- Forum: General Discussion
- Topic: 555 Timer triggered fropm a differentiator.
- Replies: 31
- Views: 19295
:smile: Hi! Al I took the servo apart and yes it has circuitry inside. I like to do my own trouble shooting but in this case I might just send it out to get fix. But before I do I’ll see if I can get a schematic for it. It’s all SMT circuitry now days and that would give me some problems, both i...
- Mon Jul 07, 2008 12:16 pm
- Forum: General Discussion
- Topic: 555 Timer triggered fropm a differentiator.
- Replies: 31
- Views: 19295
:smile: Hi! Al Well I got my project working up to the servo steering phase, would you believe it, it was the servo that was bad. The trailing edge measured 1.2 ms the stop position, and the +/- 90 degrees measured 1.22 ms which was totally not right. It was supper sensitive to the touch, so I repla...
- Wed Jul 02, 2008 8:20 am
- Forum: General Discussion
- Topic: 555 Timer triggered fropm a differentiator.
- Replies: 31
- Views: 19295
:smile: Hi! Al I'v heard so much about servo's, I thought I would do some experiments and it was great, However the servo just went +/- 90 degrees. I'm using it to steer a robot, this robot will carry an arm that I have which will pick up wooden blocks and who knows maybe bring my coffee. At 50 Hz i...
- Tue Jul 01, 2008 4:15 pm
- Forum: General Discussion
- Topic: 555 Timer triggered fropm a differentiator.
- Replies: 31
- Views: 19295