It is currently Sat Jan 20, 2018 8:31 pm

All times are UTC - 8 hours


Search found 129 matches
Search these results:

Author Message

 Forum: Articles   Topic: KReduCNC

 Post subject: KReduCNC
Posted: Mon Jan 18, 2016 11:54 am 

Replies: 0
Views: 1468


Please use this forum to post your comments or questions for the KReduCNC CNC build series.

 Forum: Articles   Topic: MF70 CNC Conversion

 Post subject: Re: MF70 CNC Conversion
Posted: Wed Feb 04, 2015 12:03 pm 

Replies: 21
Views: 4803


Here is a workflow I provided for my KRMx02 CNC. The design process is similar. http://www.kronosrobotics.com/workflow/ As for the actual gear design, you will have to purchase software to help you design gears. Involute is one and Gearotic is another. I am working on a second MF70 book and in that ...

 Forum: Articles   Topic: MF70 CNC Conversion

 Post subject: Re: MF70 CNC Conversion
Posted: Sat Jan 24, 2015 8:36 pm 

Replies: 21
Views: 4803


Thanks for the update. I will add a tip to my MF70 book to check that if you have problems.

 Forum: Articles   Topic: MF70 CNC Conversion

 Post subject: Re: MF70 CNC Conversion
Posted: Sat Jan 24, 2015 4:50 pm 

Replies: 21
Views: 4803


I have purchased six of those boards at different times and all have worked perfectly. Take a picture of the board turned on and post it so IO can take a look at it.

 Forum: Articles   Topic: MF70 CNC Conversion

 Post subject: Re: MF70 CNC Conversion
Posted: Sat Jan 24, 2015 4:30 pm 

Replies: 21
Views: 4803


One thing to make sure is that the built-in port has an EPP mode. This setting is normally set in the PC's Bios. In my books this is the first thing I tell the readers to look for when choosing a machine. Older machines did not support EPP and this may not have a parallel port that will work with Ma...

 Forum: Articles   Topic: MF70 CNC Conversion

 Post subject: Re: MF70 CNC Conversion
Posted: Fri Jan 23, 2015 2:08 pm 

Replies: 21
Views: 4803


This sounds like a Mach 3 issue and the parallel port pulse engine is not operating. 1. You have to be using a true parallel port. It can not be a usb to parallel port converter. 2. You have to make sure the parallel port settings in XP matches those in the drivers and config (Ports and pin settings...

 Forum: Articles   Topic: MF70 CNC Conversion

 Post subject: Re: MF70 CNC Conversion
Posted: Fri Jan 02, 2015 4:59 pm 

Replies: 21
Views: 4803


For you guys that have been asking, I have completed the first book on the MF70 conversion. I'm calling it "Building the KRmf70 CNC". I will be selling the book on my web site for now, but it will eventually move to Amazon and other online retailers. You can get more information here: http...

 Forum: Articles   Topic: Kronos Flyer Series

 Post subject: Re: Kronos Flyer Series
Posted: Fri Dec 05, 2014 9:32 am 

Replies: 170
Views: 25425


I have not seen this problem. You might try playing with the settings. I know they keep updating the firmware on the DJI and its hard to keep up with them. Normally the default settings worked fine.

Its possible that your ESCs need to be recalibrated.

 Forum: Articles   Topic: Kronos Flyer Series

 Post subject: Re: Kronos Flyer Series
Posted: Tue Oct 28, 2014 12:04 pm 

Replies: 170
Views: 25425


The APM promises a lot, but I have yet to get it to deliver on everything. It is not as stable as the NAZA and takes more effort just to get it running, much less full auto mode. I was never able to get the telemetry to work with the APM. Not sure it was a software or hardware issue.

 Forum: Articles   Topic: Kronos Flyer Series

 Post subject: Re: Kronos Flyer Series
Posted: Wed Sep 17, 2014 10:15 pm 

Replies: 170
Views: 25425


Look at the NAZA Lite. You can pick one up without the GPS for under $100. It will run circles around the KK2.

 Forum: Articles   Topic: Kronos Flyer Series

 Post subject: Re: Kronos Flyer Series
Posted: Tue Sep 16, 2014 7:09 pm 

Replies: 170
Views: 25425


You can mount the battery anywhere you want as long as it is centered. Top or bottom. However, if you are using a isolation platform, the battery should go on the top of the FRMP component platform. This way the isolation platform can do its job better with the added mass on the clean side of the pl...

 Forum: Articles   Topic: Kronos Flyer Series

 Post subject: Re: Kronos Flyer Series
Posted: Tue Sep 09, 2014 2:42 pm 

Replies: 170
Views: 25425


No.

Just take the existing legs and use them as a pattern to create some larger legs.

 Forum: Articles   Topic: Kronos Flyer Series

 Post subject: Re: Kronos Flyer Series
Posted: Tue Sep 09, 2014 11:44 am 

Replies: 170
Views: 25425


I ran out of room in my current lab and shop. I am in the process of building a new one (Converting a barn I built a while back). Wont do any more books or articles until the conversion is complete.

Here is my blog for the conversion:
http://www.obsessiveme.com/new-shop-and-lab/

 Forum: Articles   Topic: Kronos Flyer Series

 Post subject: Re: Kronos Flyer Series
Posted: Tue Sep 09, 2014 9:32 am 

Replies: 170
Views: 25425


I have designed taller legs for my drone book. The goal is to give enough clearance for a gimbal.

 Forum: Articles   Topic: Kronos Flyer Series

 Post subject: Re: Kronos Flyer Series
Posted: Sun Sep 07, 2014 6:59 pm 

Replies: 170
Views: 25425


The isolation platform is only needed if you want to use a camera or FPV. It is used to keep the vibration from interfering with the cameras. In addition some controllers like the APM my need some isolation or they will perform badly. The isolation platform has the same hole pattern on the top as th...
Sort by:  
Page 1 of 9 [ Search found 129 matches ]


All times are UTC - 8 hours


Jump to: